Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Keypad & Intercom Repair: The Santa Clarita Owner’s Guide
Ghost Controls keypad and intercom repair in Santa Clarita typically runs $145 to $310 installed, and we stock the common Ghost Controls-compatible keypads and intercom modules on our trucks so most calls are same-day. Most Santa Clarita homeowners discover the failure the same way: they punch in the code, hear either nothing or a faint click, and end up walking through the pedestrian gate or driving around to the other side. The keypad looks fine from the outside. The board inside is another story.
We have repaired Ghost Controls entry systems in Valencia, Saugus, Newhall, and up through Canyon Country long enough to know which failures are weather-related and which are wiring-related. This page gives you the straight diagnosis picture, the real cost, and what we leave behind when we finish.
Which Ghost Controls Models This Applies To
The Ghost Controls keypad line splits into two families: the AXS series (AXS-1 keypad, AXS-3 wireless keypad) and the older GCP keypad models paired with the Gate Opener System (typically GPM-1 and GPM-2 motor kits). The AXS-3 is the current workhorse, and it is the one we see most often in Santa Clarita driveways, particularly on single-swing gates in the Newhall Ranch and Tesoro Del Valle neighborhoods. Identifying your unit is straightforward: the model label sits on the back of the keypad housing, and the AXS-3 will say “AXS-3” or “KP3” in the fine print under the battery tray. The older GCP keypad usually carries a “GCP-KP” marking.
One Ghost Controls-specific note worth knowing: the AXS-3 is not backward-compatible with GCP-series receiver modules without a firmware match, so guessing the part number from an online search often ends in a mismatched receiver that binds but will not hold a signal beyond 15 feet. We carry both lines and match by receiver date code, not just by keypad model. For intercom work, we use OEM Ghost Controls boards where the system is factory-wired, and a hard-wired video intercom retrofit where the original audio-only intercom has outlived its useful service window. We stock OEM and quality aftermarket equivalents, and we tell you which one makes sense before we install it.
Signs Your Ghost Controls Keypad & Intercom Repair Is Failing
- Keypad accepts the code but the gate doesn’t move. The keypad’s transmitter is sending a signal, but the receiver board on the gate opener isn’t hearing it. Usually the receiver’s antenna wire has corroded or pulled loose inside the control box. We find this on gates that sit close to sprinkler runs in Valencia.
- Keypad is completely dead, no backlight, no beep. Either the battery contacts have corroded or water has crept past the seal and shorted the board. Santa Clarita summer heat breaks down the rubber gasket faster than most manuals claim.
- Intercom buzzes or hums but the voice is garbled. This is typically a failing capacitor on the intercom board or a bad speaker cone. It starts intermittent in hot weather, then goes permanent.
- Gate opens on its own or won’t close when visitors key in. A stuck or shorted key on the membrane pad can send repeated signals. We see this most on pedestal-mounted Ghost Controls keypads that face afternoon sun up Sand Canyon Road.
- Water or condensation inside the keypad lens. Once moisture is visible inside the housing, the circuit board is already corroding. The unit will fail fully within a season unless the seal is replaced and the board cleaned or swapped.
BeforeAfterReplacement Cost & What’s Included
In Santa Clarita, our Ghost Controls keypad replacement runs $145 to $230 installed for the AXS-3 keypad and receiver pairing, and $180 to $310 when we are replacing a failed intercom module or retrofitting an audio intercom to a video unit. The spread comes down to which part family you have, whether the receiver needs replacing alongside the keypad, and whether we need to run a fresh low-voltage line from the keypad pedestal to the control box. You will know the exact number before we touch a screwdriver. The written price covers the part, the labor, the programming of all user codes, and the photo record we leave behind, per Haven Standard Clause 1.
Every Ghost Controls keypad or intercom job we do in Santa Clarita carries our 365-Day Done Right Promise. If the unit fails within a year, we return and fix it at no charge. No argument, no fee, no expiration date within that window.
DIY or Call Us?
You can safely check three things on a dead Ghost Controls keypad: replace the batteries with fresh AA or AAA cells (match what is printed in the tray), confirm the breaker for the gate opener is on, and look for visible water inside the lens. Those three checks take ten minutes and cost nothing. What you should not do is open the keypad housing and start probing the board while the gate opener is still powered, because the low-voltage line can still carry a short back to the control panel and damage the receiver board. We have arrived at more than one Santa Clarita home where a homeowner’s $20 multimeter check turned a $180 keypad swap into a $340 receiver and board replacement.
If your Ghost Controls keypad or intercom is acting up and you would rather have it diagnosed in one visit with a written price before the work starts, call us at (747) 294-2900. A live person answers, any hour, any day.
FAQs
Plan on 4 to 7 years for a Ghost Controls AXS series keypad in Santa Clarita’s climate, with sun exposure being the biggest variable. Units mounted facing west or southwest, especially in Canyon Country and along Soledad Canyon Road, tend to fail closer to the 4-year mark as the housing seal degrades and the membrane keypad stiffens. Call us at (747) 294-2900 if yours is starting to act up. We can tell you over the phone whether it sounds like a battery issue or board failure.
Yes, when the failure is a speaker cone, a capacitor, or a corroded wire terminal, an intercom can be repaired on-site, and we stock those components on our trucks. When the main board has water damage across multiple traces, the repair cost often equals or exceeds a new module, and we will tell you that plainly before recommending the swap. The price is written before any work starts.
Most keypad replacements in Santa Clarita take 40 to 75 minutes from arrival to programming, assuming the existing wiring is intact and the receiver is healthy. If we need to run a new low-voltage line or replace the receiver as well, expect up to two hours. We will give you the time estimate in writing when we arrive, and the work is done the same day.
We stock GH Controls AXS-3 keypads, GCP-series compatible keypads, receiver modules, gasket kits, and intercom boards on our service vehicles, so most Santa Clarita calls get same-day service. If your setup is older or requires a specific firmware match, we’ll have the exact part in hand within two business days and schedule the install around you. When you call (747) 294-2900, tell us the model number from the back of the keypad and we can confirm what is on the truck before we dispatch.
Call Vance Gate Repair Santa Clarita for Ghost Controls Keypad & Intercom Work
We service Ghost Controls systems along with LiftMaster, Mighty Mule, DoorKing, and six other automation brands across Santa Clarita. When Adrian Vance started this company in 2014 after years in commercial access control, he kept the documentation habits that keep customers from paying twice for the same repair. Name what you found. Name what it costs. Name what you left behind. That is the standard on every Ghost Controls keypad and intercom job we do.
Call us at (747) 294-2900 for a free estimate. You will get a written price before work begins, a documented photo record when the job is done, and a live person on the phone at any hour.
Written by Adrian Vance, Owner, Vance Gate Repair Santa Clarita, serving Santa Clarita and nearby areas.